View ADC-8032A_168883.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ross Video Limited
ADC-8032A ADC-8032A-S
Analog Composite to SDI Decoder
User Manual
Ross Part Number: 8032AD-004 Issue: 04
ADC-8032A * Analog Composite to SDI Decoder User Manual
* * * * Ross Part Number: 8032AD-004 Document Issue: 04 Printing Date: November 12, 2003. Printed in Canada. Software Issue: 1.00
The information contained in this User Manual is subject to change without notice or obligation.
Copyright
(c) 2003 Ross Video Limited. All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of Ross Video Limited. Reproduction or reverse engineering of copyrighted software is prohibited.
Notice
The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as a commitment by Ross Video Limited. Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.
Trademarks
* * * is a registered trademark of Ross Video Limited. and MLE are registered trademarks of Ross Video Limited. Ross, ROSS, All other product names and any registered and unregistered trademarks mentioned in this manual are used for identification purposes only and remain the exclusive property of their respective owners. ROSS ,
Important Regulatory and Safety Notices to Service Personnel
Please review the following material to avoid injury to personnel and to prevent product damage. * * All product servicing should be carried out by qualified service personnel. This product may require specific equipment, and/or installation procedures to be carried out to satisfy certain regulatory compliance requirements. The following notices have been included in the manual, to call attention to these specific requirements.
Symbol Meanings
* Protective Earth -- This symbol alerts the user of the need to have a protective grounding source to avoid damage to electronic components. Caution -- This symbol alerts the user to a procedure which may cause irreversible problems. Refer to important safety and compliance information. Warning Hazardous Voltages -- This symbol alerts the user to the presence of an insulated dangerous voltage within the enclosure of the product.
*
*
Important Safety Instructions
* * * * * Do not use this device near water. Hazardous voltages can occur. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. Do not defeat the safety purposes of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the device. Only use attachments/accessories specified by the manufacturer. Unplug this apparatus during lightning storms or when not in use for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as: power-supply cord or plug is damaged, objects have fallen into the device, the device has been exposed to rain or moisture, the device does not operate normally or has been dropped.
* * * *
Power Cord and Supply Grounding Requirements
The safe operation of this product requires that a protective earth connection be provided. This protective earth is provided by the grounding conductor in the equipment's supply cord. To reduce the risk of electrical shock to operator and service personnel, this ground conductor must be connected to an earthed ground. This product is equipped with a Class 1 Type power supply, which for safe operation requires the use of a protective earth connection. To reduce the risk of electrical shock, use only properly earthed three-conductor type line cords as outlined below: * North American Line Cords 100 - 120 Volts In North America, use only certified IEC 320-C13, 10A/125V, SVT type line cords. Conductors are CEE color coded blue (neutral), brown (line) and green/yellow (ground). North American product orders come equipped with a single 10A/125V SVT type line cord for each RossGear or GearLite product ordered. * International Line Cords 200 - 240 Volts This product is designed for use with certified IEC 320-C13, 10A/250V - H03 VV-F3G 1.00mm2 type line cords. International product orders come equipped with a single certified 10A/250V line cord, utilizing a molded 3-pin IEC 320-C13 type connector at one end and stripped conductors at the other. Conductors are CEE color-coded: blue (neutral), brown (line), and green/yellow (ground). Installation of an appropriately approved A/C wall plug certified for the country of use by a qualified electrician is required. Alternatively, other IEC 320 C-13 type power supply cords may be used provided that they meet all safety requirements necessary for the country in which they are to be used.
EMC Notices
* FCC This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense. * CE This product has been tested and meets the requirements of the European CE marking directive. A copy of the CE Declaration of Conformity can be provided upon request.
Maintenance/User Serviceable Parts
Routine maintenance to this RossGear or GearLite product is not required. This product contains no user serviceable parts. If the module does not appear to be working properly, please contact Technical Support using the numbers listed under the "Contact Us" section on the last page of this manual. All RossGear GearLite products are covered by a generous 3-year warranty and will be repaired without charge for materials or labor within this period. See the "Warranty and Repair Policy" section in this manual for details.
Contents
Introduction 1-1
In This Chapter .......................................................................................................................1-1 A Word of Thanks....................................................................................................1-1 Overview ..................................................................................................................1-1 Functional Block Diagram .......................................................................................1-2 Features ....................................................................................................................1-3 Documentation Terms ..............................................................................................1-4 Abbreviations ...........................................................................................................1-4
Installation and Setup
2-1
In This Chapter .......................................................................................................................2-1 Static Discharge........................................................................................................2-1 Unpacking ................................................................................................................2-1 Jumper Setup ............................................................................................................2-2 Board Installation .....................................................................................................2-3 Cable Connections....................................................................................................2-3
User Controls
3-1
In This Chapter .......................................................................................................................3-1 User Controls............................................................................................................3-2 Troubleshooting Checklist .......................................................................................3-4
Using Banks
4-1
In This Chapter .......................................................................................................................4-1 General Operating Rules ..........................................................................................4-1 Selecting Banks ........................................................................................................4-2 Using Bank A Functions ..........................................................................................4-6 Using Bank B Functions.........................................................................................4-11 Using Bank C Functions.........................................................................................4-13 Timing Modes ........................................................................................................4-15
SMPTE 269M Fault Reporting
5-1
In This Chapter .......................................................................................................................5-1 Overview ..................................................................................................................5-1 Jumper Setup ............................................................................................................5-2 Frame Connections...................................................................................................5-2 Details.......................................................................................................................5-2
Comlink
6-1
In This Chapter .......................................................................................................................6-1
ADC-8032A User Manual (Iss. 04)
Contents * i
Overview ................................................................................................................. 6-1 Cable Construction .................................................................................................. 6-2 Connection and Configuration ................................................................................ 6-3
Specifications
7-1
In This Chapter ...................................................................................................................... 7-1 Technical Specifications.......................................................................................... 7-2
Ordering Information
8-1
In This Chapter ...................................................................................................................... 8-1 ADC-8032A and Related Products ......................................................................... 8-1 Warranty and Repair Policy .................................................................................... 8-2
ii * Contents
ADC-8032A User Manual (Iss. 04)
Introduction
In This Chapter
This chapter contains the following information sections: * * * * * A Word of Thanks Overview Functional Block Diagram Features Documentation Terms
A Word of Thanks
Congratulations on choosing the Ross Video ADC-8032A Analog Composite to SDI Decoder. You have purchased a powerful, versatile, and advanced decoder. The ADC-8032A is part of a full line of Digital Conversion Products within the RossGear Terminal Equipment family of products, backed by Ross Video's experience in engineering and design expertise since 1974. You will be pleased at how easily your new ADC-8032A fits into your overall working environment. Equally pleasing is the product quality, reliability and functionality. Thank-you for joining the group of worldwide satisfied Ross Video customers! Should you have a question pertaining to the installation operation of your ADC-8032A, please contact us at the numbers listed in this publication. Our technical support staff is always available for consultation, training, or service.
Overview
The ADC-8032A Analog Composite to SDI Decoder is a 10-bit broadcast quality decoder with a 12bit analog to digital converter. It is specifically designed for broadcast or production situations in which an analog PAL, PAL-M, PAL-N, or NTSC composite signal must be converted to a component SDI signal. Four SDI outputs are provided. The ADC-8032A fits into the Ross 8000 series digital frames, with four cards in the DFR-8104A (1RU), and up to ten cards in the DFR-8110A (2RU). Please refer to the frame User Manual for specific ventilation and cooling instructions to maintain optimum operating conditions. This card also fits into Leitch* FR-6800 series frames to provide you with greater installation versatility. The ADC-8032A is available in two different models: * Leitch is a trademark of Leitch Technology Corporation
ADC-8032A User Manual (Iss. 04)
Introduction * 1-1
* *
ADC-8032A - The base model decoder includes Proc Amp, Line Delay, and Line Synchronizer timing modes. ADC-8032A-S - The "S" model includes a Frame Synchronizer, along with all the features available on the ADC-8032A
The ADC-8032A-S version comes with a fully functional frame synchronizer, capable of synchronizing incoming video to house reference. Various timing modes are available to accommodate most situations. New techniques in frame synchronization contribute to the board's low power requirements and compact design. The complete circuit for the ADC-8032A, including a 12-bit A-D converter, decoder, frame (or line) synchronizer, serializer, TTL tracking delay pulse, and microprocessor is contained on a single DA-sized card. Additional daughter cards are not required. A rich set of features is instantly accessible using simple card-edge switches and controls in conjunction with a concise Heads-Up Display. The ADC-8032A's 10-bit decoding process provides excellent performance with all types of picture sources. In order to achieve the highest level of precision, all signal processing and decoding is performed entirely in the digital domain. The decoder uses a very sophisticated 5-line comb filter with advanced adaptive control algorithms. To make configuration simple and easy, the ADC-8032A offers a Heads-Up Display mode for most board-level adjustments. This display is especially convenient during setup, and for programming several ADC-8032A cards with identical configurations. With the display enabled, the parameter currently being adjusted has its value super-imposed over all board outputs. As an alternative to the Heads-up Display, the board's Comlink Terminal Display allows you to view all settings simultaneously on any PC running VT-100 terminal emulation. The only requirement is a connection between the PC's serial port and the ADC-8032A's Comlink connector. This feature is especially convenient for making adjustments while the card's output is on air. The ADC-8032A and the ADC-8032A-S decoders are part of a full line of RossGear digital distribution products engineered to satisfy the highest quality broadcast standards and the most demanding requirements of your facility.
Functional Block Diagram
SDI OUT NTSC PAL PAL-M PAL-N 5-Line Aperture Input Adaptive Filter & Decoder Clamp & TBC EDH Insertion & SDI Serializer
Analog IN:
Input Filter & Clamp
12-Bit ADC
Line Synchronizer
Ross Frame Reference IN Color Black Reference IN Alternate Reference
Master Reference
TTL Tracking Delay pulse Tracking OUT
Frame Synchronizer (-S Version)
Figure 1. Simplified Block Diagram of ADC-8032A Functions
1-2 * Introduction
ADC-8032A User Manual (Iss. 04)
Features
The following features make the ADC-8032A Analog Composite to SDI Decoder the most flexible, high-quality decoding card for your analog to digital conversion requirements: * * * * * * * * * * * * * * * * * * * * * * * * * 10-bit decoding with 5-line adaptive comb filter 12-bit analog to digital conversion Handles difficult signals such as satellite or microwave feeds Compact design on a single DA-sized card Heads-Up display Optional Frame Synchronization (no daughter card required) Field-upgradeable Frame Synchronization option available Extensive Proc Amp controls Freeze modes Hot-switching Horizontal and vertical timing adjustments Programmable vertical interval blanking Setup adjustment Black level offset Super black control Input and conversion status indicator LED's on card edge Auto-detects NTSC/PAL Jumper-selectable PAL-M/PAL-N Choice of reference inputs Four serial digital outputs TTL Tracking Delay Output for companion audio synchronizer Comlink terminal display SMPTE 269M Fault Reporting Fits Ross Video 8000 series digital products frames and Leitch FR-6800 series frames 5-year transferable warranty
ADC-8032A User Manual (Iss. 04)
Introduction * 1-3
Documentation Terms
The following terms are used throughout this guide: * * "Frame" refers to the DFR-8104A and DFR-8110A frames that house the ADC8032A card. All references to the DFR-8104A and DFR-8110A also include the DFR-8104A-C and DFR-8110A-C versions with the cooling fan option. See the respective User Manuals for details. "Operator" and "User" both refer to the person who uses the ADC-8032A. "Board", "Card", and "Module" all refer to the ADC-8032A decoder board itself, including all components and switches. "System" and "Video system" refers to the mix of interconnected digital and analog production and terminal equipment in which the ADC-8032A operates. "525-line mode" refers to broadcast situations using NTSC or PAL-M composite (analog) signal reference inputs. "625-line mode" refers to broadcast situations using PAL-B or PAL-N composite (analog) signal reference inputs. All references to PAL in this manual imply that PAL-B is being used. All references to PAL-N are "combination N" (ITU-R BT. 470-6)
* * * * *
*
Abbreviations
The following abbreviations may be used throughout the text:
Abbreviation
ADC A-D D-A DA DAC DDR DIS DVR EN LOW SIG RU SDI VCR VTR
Definition
Analog to Digital Converter Analog-to-Digital Digital-to-Analog Distribution Amplifier Digital to Analog Converter Digital Disk Recorder Disable Digital Video Recorder Enable Low Signal Rack Unit Serial Digital Interface Video Cassette Recorder Video Tape Recorder
1-4 * Introduction
ADC-8032A User Manual (Iss. 04)
Installation and Setup
In This Chapter
This chapter contains the following information sections: * * * * * Static Discharge Unpacking Jumper Setup Board Installation Cable Connections
Static Discharge
Whenever handling the ADC-8032A and other related equipment, please observe all static discharge precautions as described in the following note: Static discharge can cause serious damage to sensitive semiconductor devices. Avoid handling circuit boards in high static environments such as carpeted areas, and when wearing synthetic fiber clothing. Always exercise proper grounding precautions when working on circuit boards and related equipment.
Caution
Unpacking
Unpack each ADC-8032A you received from the shipping container, and check the contents against the packing list to ensure that all items are included. If any items are missing or damaged, contact your sales representative or Ross Video directly.
ADC-8032A User Manual (Iss. 04)
Installation and Setup * 2-1
Jumper Setup
Use the following steps to set up ADC-8032A jumpers. These steps are performed before installing the unit in the frame, but may be repeated as required. Refer to Figure 2 for card jumper locations.
Figure 2. ADC-8032A Jumper Locations
1.
Using the figure above and the card silk-screening, set JP5 (Input Select) to select the input video standard: * * * Set jumper on pins 1-4 (Auto) to automatically select between NTSC and PAL (default setting) Set jumper on pins 2-5 (PAL-M) for PAL-M decoding Set jumper on pins 3-6 (PAL-N) for PAL-N decoding
2.
An analog composite reference is required for Line Sync and Frame Sync modes. Using the figure above and the card silk-screening, set Jumper JP3 (Ext Ref) to determine the location from which you want to obtain external reference. * * Set jumper on pins 1-2 (Frame) to obtain the reference from the frame's master reference (analog reference) connector (default setting) Set jumper on pins 2-3 (O/P8) to obtain the reference from connector 8 on the back-plane
3.
(Optional) Using the figure above and the card silk-screening, set Jumper JP4 (269M Fault Reporting) to enable or disable the card's SMPTE alarm: * * Set jumper on pins 1-2 (EN) to enable SMPTE fault reporting (default setting) Set jumper on pins 2-3 (DIS) to disable SMPTE fault reporting
(See Chapter 5, "SMPTE 269M Fault Reporting" for details on fault reporting.)
2-2 * Installation and Setup
ADC-8032A User Manual (Iss. 04)
Board Installation
Use the following steps to install the ADC-8032A in a RossGear 8000 series digital distribution frame: 1. Refer to the User Manual of the RossGear 8000 series frame, to ensure that the frame is properly installed according to instructions. If this module is to be installed in any compatible frame other than a Ross Video product, refer to the frame manufacturer's manual for specific instructions. Please note that heat and power distribution requirements within a frame may dictate specific slot placement of cards. Cards with many heat-producing components should be arranged to avoid areas of excess heat build-up, particularly in frames using convectional cooling. After selecting the desired frame installation slot, hold the ADC-8032A card by the edges and carefully align the card edges with the slots in the frame. Then fully insert the card into the frame until the rear connection plug is properly seated.
2.
3.
Cable Connections
This section provides instructions for connecting cables to the ADC-8032A when mounted in RossGear 8000 series Digital Products Frames. See the following frame rear panel diagram for BNC input and output designations:
IN
SDI Out 2
Analog Composite Video In SDI Out 1
2
SDI Out 4
4
1
SDI Out 3
3
TTL Tracking Delay Pulse Color Black Reference In
6
Not Used
5
8
Comlink
7
Figure 3. ADC-8032A BNC Designations for RossGear Frames
Connect the BNC cables as follows: 1. 2. 3. Connect the Analog Composite IN BNC connector to the output of your analog composite device. Connect BNCs 1 through 4 to the inputs of four component SDI devices. Connect BNC 6 to any device that needs to track the video delay through the 8032A or 8032A-S. (RossGear ADL-8520 AES/EBU Auto Tracking Audio Delay) The TTL Tracking Delay Pulse is a positive 5V pulse. Its width tracks the video delay as it passes through the card. The ADC-8032A TTL pulse tracks up to 2 video lines, the ADC-8032A-S up to 2 fields. 4. If you wish to use the Comlink functionality, connect the BNC end of the Comlink adapter cable (not supplied) to BNC 7. See Chapter 6, "Comlink" for details on this optional feature. Connect a video reference one of two ways:
5.
ADC-8032A User Manual (Iss. 04)
Installation and Setup * 2-3
*
If you wish to obtain the reference directly from the card's back plane, connect a composite analog color black reference to BNC 8. Be sure that pins 2-3 (O/P8) are shorted on Jumper JP3. Please refer to the previous section entitled, "Jumper Setup".
Note
BNC 8 is terminated at 75-ohms on the card. * If you wish to reference the card from the frame's Master Reference connector, ensure that a composite analog color black reference signal is connected to the REF BNC on the frame (see Figure 6 in chapter 5). Be sure that Jumper JP3 is set to pins 1-2 (Frame).
2-4 * Installation and Setup
ADC-8032A User Manual (Iss. 04)
User Controls
In This Chapter
This section contains the following sections: * * Note User Controls Troubleshooting Checklist
The ADC-8032A uses card edge controls for changing operational parameters. The card defaults with switch access set to the locked position. Refer to the "Bank A - F: Lock/Unlock Switch Access" section in Chapter 4, "Using Banks", before attempting to make any adjustments.
ADC-8032A User Manual (Iss. 04)
User Controls * 3-1
User Controls
The following are general descriptions of the user controls identified in the figure below, presented in normal operating sequence.
Input OK LED Error LED
6
SW1 Function Select Switch SW2 Mode Select Switch Bank A LED Bank B LED Bank C LED In 525 LED In 625 LED Ref OK LED Freeze LED Access LED ID Select Switch Fine Phase Adjust Pot
Figure 4. ADC-8032A Card-edge User Controls
SW1 - Function Select Switch
The SW1 Function Select switch is a 16-position rotary switch used to select functions such as decoder channel, video standard, and video setup menu items. The SW1 switch works in conjunction with the SW2 toggle switch; first, the function category is selected with SW1, and then the SW2 toggle switch is used to select modes or configuration settings within that function selection. See Chapter 4, "Using Banks" for complete details.
SW2 - Mode Select Switch
The SW2 Mode Select switch is used to enable, disable, and select specific ADC-8032A functional modes, or configurations, within the operational function menu (selected first with the SW1 Function Select switch). The Mode Select switch is a 3-position momentary toggle switch with an automatic spring-return to the center (null or unity) position. Two methods of toggling SW2 are used to select basic and advanced level menu items. * * * * Single toggle to select single options Hold toggle to scroll through multiple values or options menu selections utilizing a scrolling wrap-around style of selection (from last menu item directly back to first menu item) menu selections utilizing a bi-directional upper and lower range limit
Toggling the switch for menu selection is made according to two basic menu design categories:
ID Select Switch
No user adjustment required.
3-2 * User Controls
ADC-8032A User Manual (Iss. 04)
Fine Phase Adjust Potentiometer
The RV1 Fine Phase Adjust potentiometer adjusts the board's output delay in sub-pixel increments, with a range of 0 (zero) to approximately 45ns.
Status and Selection LEDs
The front edge of the card features ten LEDs that display the status of the input signals, and indicate menu function and configuration selections. As selections are made from the menu tables, (see Chapter 4, "Using Banks" for complete bank menu table descriptions), the LEDs display the status of the input signals for each bank, as well as menu function and configuration selections. Basic LED displays and descriptions are provided in the following table:
Table 1. Selection and Status LED Descriptions
LED
Color
Display and Description
When lit, this LED indicates that the card is functioning normally and that no anomalies have been detected. Both of the following conditions must be satisfied: * A valid input signal is present * A valid reference signal is present when a reference is required, and that the reference standard matches the input standard. Selecting Line Sync or Frame Sync modes require that a reference signal is present When lit, this LED indicates that conditions for INPUT OK are not met. Mutually exclusive with INPUT OK LED. When lit, this LED confirms that Bank A is selected. When lit, this LED confirms that Bank B is selected. When lit, this LED confirms that Bank C is selected. Lights when the input signal is 525-lines (NTSC or PAL-M). Lights when the input signal is 625-lines (PAL or PAL-N). When lit, this LED indicates a reference signal is present at the Master REF or BNC input, and that the reference signal is locked. * On = External reference standard matches the input standard * Flashing = External reference standard does not match the input standard * Off = No external reference is present When lit, this LED indicates that any freeze mode is enabled (both models). When lit, this LED indicates that Switch Access is unlocked. See Bank A Functions, Mode Select position F. All changes made with Mode Select will affect ADC-8032A operation.
INPUT OK
Green
ERROR BANK A BANK B BANK C IN 525 IN 625
Red Green Green Green Green Green
REF OK
Green
FREEZE ACCESS
Yellow Yellow
ADC-8032A User Manual (Iss. 04)
User Controls * 3-3
Troubleshooting Checklist
Routine maintenance to this RossGear product is not required. In the event of problems with your ADC-8032A, the following basic troubleshooting checklist may help identify the source of the problem. If the module still does not appear to be working properly after checking all possible causes, please contact your Ross Video products distributor, or the Ross Video Technical Support department at the numbers listed under the "Contact Us" section at the end of this manual. 1. Visual Review - Performing a quick visual check may reveal many problems, such as connectors not properly seated or loose cables. Check the module, the frame, and any associated peripheral equipment for signs of trouble. Power Check - Check the power indicator LED on the distribution frame front panel for the presence of power. If the power LED is not illuminated, verify that the power cable is connected to a power source and that power is available at the power main. Confirm that the power supplies are fully seated in their slots. If the power LED is still not illuminated, replace the power supply with one that is verified to work. Reseat the Card in the Frame - Eject the card and reinsert it in the frame. Check Control Settings - Refer to the Installation and Operation sections of the manual and verify all user-component settings including correct BNC designations. Input Signal Status - Verify that source equipment is operating correctly and that a valid signal is being supplied. Output Signal Path - Verify that destination equipment is operating correctly and receiving a valid signal. Module Exchange - Exchanging a suspect module with a module that is known to be working correctly is an efficient method for localizing problems to individual modules.
2.
3. 4.
5. 6. 7.
3-4 * User Controls
ADC-8032A User Manual (Iss. 04)
Using Banks
In This Chapter
This section provides a detailed explanation on using Bank functions. The following topics are discussed: * * * * * * General Operating Rules Selecting Banks Using Bank A Functions Using Bank B Functions Using Bank C Functions Timing Modes
General Operating Rules
Please note the following important operating rules for the ADC-8032A: * Note Whenever the card is powered up, it defaults to Bank A, and the Bank A LED is lit.
The card defaults with switch access set to the locked position. To unlock the access refer to the "Bank A-F: Lock/Unlock Switch Access" section in this chapter before attempting to make any adjustments. * For each of the supported video formats (NTSC / PAL / PAL-M / PAL-N) the card stores the default or user-adjusted video settings independently in non-volatile memory. The selection of settings is determined by the setting of JP5 Input select, the video standard jumper. Always check to see that the Input OK LED is lit. If not, check that the inputs are valid. If a reference is used, check that the reference is valid and that the reference standard matches the input standard. Before making adjustments, choose the method that you wish to use. Three methods are available:
*
*
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-1
1.
No display - Adjustments are made using the Function Select and Mode Select switches, without the assistance of the Heads-Up Display or the Comlink Display. Results should be confirmed with test equipment suitable for measuring the parameter being adjusted (such as a waveform monitor or vector scope). Heads-Up Display - Adjustments are made using Function Select and Mode Select switches in conjunction with the Heads-Up Display. Ensure that the Heads-Up Display is enabled (Bank A, Position 1). Note that the display is superimposed over all ADC-8032A video outputs. Terminal Display - Adjustments are made using Function Select and Mode Select switches in conjunction with the Comlink Display. Ensure that the Comlink port is properly connected to a PC. Refer to Chapter 8, "Comlink" for instructions.
2.
3.
Note
Both the Heads-Up Display and the Comlink Display can be used simultaneously.
Operating Conventions For Function Tables
The following rules apply to the function tables that are used throughout this section: * * * * The label " + " instructs you to toggle the Mode Select switch (SW2) up momentarily. The label " - " instructs you to toggle the Mode Select switch (SW2) down momentarily. The label " + (h) " instructs you to hold the Mode Select switch (SW2) up for one second. The label " - (h) " instructs you to hold the Mode Select switch (SW2) down for one second.
Selecting Banks
Function Select switch functionality is divided into three banks of functions. Use the following steps to select Bank A, B or C as required. 1. 2. 3. Rotate Function Select (SW1) to position 0. Note that position 0 is always used to select the bank, regardless of the bank that you are currently using. Toggle Mode Select (SW2) up or down to choose the desired bank. Three positions are available: Bank A, B or C. The table below illustrates each switch function, along with the Heads-Up Display label, the Status LED indication, and the default value. If you are not using a display, be sure to verify your selection on the Status LED's.
Table 2. Switch and Bank Selection
Mode Select SW2
+ A B C
Heads-up Display Label
BANK A BANK B BANK C
Status LED
BANK A BANK B BANK C
Default Bank
A A A
4-2 * Using Banks
ADC-8032A User Manual (Iss. 04)
Bank A, B, and C Function Tables
This section presents a detailed charting of all board-level ADC-8032A functions in the following three tables. The operational usage is explained in the next section.
Table 3. Function Select: Bank A Function Table
SW1 Function Select
0 1 2 3 4 5 6 7 8 9 A B C D E F
Function
SW2 Mode Select Options
+ A B C On Off
Heads Up Display On-Screen Label and Value
BANK A B C ON OFF
Default Value
A OFF
Bank Select Heads-Up Display N/A N/A N/A N/A N/A N/A Video Gain m Black Level Offset m Chroma Gain m Hue m CB Gain m Chroma AGC Factory Defaults Switch Access ** + + + + + + + (h) -
HEADS UP
Increase Decrease Increase Decrease Increase Decrease Increase Decrease Increase Decrease On Off
VID GAIN BLK OFF CHROMA HUE C B GAIN CHROMA AGC
(###.#)% (##.#) IRE (###.#)% (###.#) DEG. (###.#)% ON OFF
100% * 0 IRE * 100% * 0 DEG. * 100% * OFF *
+ (h) Reset All DEFAULT - (h) Reset Proc Amp + - (h) Locked Unlocked ACCESS
ALL RST N/A PROC RST LOCKED LOCKED UNLOCKED
Note: Functions, as listed in the Function column as being stored in memory, always power up in the last known state. All other items, however, power up in the default state, regardless of their previous state. * Indicates Proc Amp controls that are affected by position E, Factory Defaults function. ** Locking Switch Access shuts off the Heads-up Display. Unlocking will not restore the display if it was previously enabled. This must be performed manually. m Stored in memory
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-3
Table 4. Function Select: Bank B Function Table
SW1 Function Select
0 1 2 3 4 5 6 7 8 9 A B C D E F
Function
SW2 Mode Select Options
+ A B C On Off Blank Pass Through Increase Decrease Pass Through Clip Line 20 Line 10
Heads Up Display On-Screen Label and Value
BANK A B C ON OFF A
Default Value
Bank Select Setup m N/A VI Blanking m VI End m SuperBlack m V Bit Lock m N/A N/A N/A N/A N/A N/A N/A N/A N/A + + + + + -
SETUP
ON* OFF **
VI BLANK VI END SUPER BLK V BIT LOC
BLANK PASS PASS (##) PASS CLIP 20 10 20 PASS 20
Note: Functions, as listed in the Function column as being stored in memory, always power up in the last known state. All other items, however, power up in the default state, regardless of their previous state. * Indicates default PAL/PAL-N setting. ** Indicates default NTSC/PAL-M setting. m Stored in memory
4-4 * Using Banks
ADC-8032A User Manual (Iss. 04)
Table 5. Function Select: Bank C Function Table
SW1 Function Select
0
Function
SW2 Mode Select Options
+ A B C Frame Sync* Frame Delay* Line Sync Line Delay Increase Decrease Zero No action Increase Decrease Zero No action Zero No action VTR input Standard input Frame Field 2 Field 1 Freeze** Pass Through Freeze** No Output Black
Heads Up Display OnScreen Label and Value
BANK A B C FS FD LS LD (####) ZERO (#) ZERO ZERO VTR STAND FRAME FLD 2 FLD 1 FORCE PASS RE-INIT FREEZE NO OUTPUT BLACK FREEZE BLACK OFF ON OFF ON OFF
Default Value
A LS (FS on S model) 0 N/A 0 N/A N/A STAND FLD 1 PASS
Bank Select +
TIME MODE
1
Timing Mode
m
m
2 3 4 5 6 7 8 9
H Delay H Reset V Delay V Reset
m
Set Min. Delay Input Mode
m
m Freeze Mode , **
+ + + + + + + + + -
H DELAY H RESET V DELAY V RESET MIN DEL IN MODE FRZ MODE
Forced Freeze
m
FREEZE IN LOSS
A
Input Loss Mode
BLACK
B C D E F
Hotswitch Mode Forced Black Forced Mono
m
Freeze** Black Off + (h) On Off + (h) On Off
+ -
HOTSW MD
OFF OFF OFF
FRCD BLK FRCD MONO
N/A N/A Note: Functions, as listed in the Function column as being stored in memory, always power up in the last known state. All other items, however, power up in the default state, regardless of their previous state. * Only available on ADC-8032A-S. ** When Freeze mode is activated the freeze will affect either field 1, field 2, or the entire frame. m Stored in memory
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-5
Using Bank A Functions
The following topics are discussed in this section: * * * * * * * * * Important Heads-up Display Video Gain Black Level Offset Chroma Gain Hue CB Gain Chroma AGC Factory Defaults Lock/Unlock Switch Access
The card defaults with switch access set to the locked position. To unlock the access refer to the "Bank A-F: Lock/Unlock Switch Access" section in this chapter before attempting to make any adjustments.
Bank A-1: Heads-up Display
Use the following steps to enable or disable the Heads-up display: 1. 2. Select Bank A, and rotate SW1 Function Select to position 1. Choose the desired display mode: * * Hold Mode Select up for one second to enable the display. Hold Mode Select down to disable the display.
Bank
A
SW1 Function Select
1
SW2 Mode Select
+ (h) On Off
Heads-Up Display Label
HEADS UP ON OFF
Default
OFF
Note
The display is superimposed over all ADC-8032A video outputs. Do not use this feature with "on-air" signals.
4-6 * Using Banks
ADC-8032A User Manual (Iss. 04)
Bank A-8: Video Gain
Use the following steps to adjust the ADC-8032A's output video gain: 1. 2. Select Bank A, and rotate Function Select to position 8. Adjust video gain up or down as required: * * * * Toggle Mode Select up to increase video gain. Hold Mode Select up to increase video gain continuously. Toggle Mode Select down to decrease video gain. Hold Mode Select down to decrease video gain continuously.
Bank
A
SW1 Function Select
8
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
VID GAIN (###.#)%
Default
100%
Note
Video Gain is one of the six "Proc Amp" controls that can be reset using Factory Defaults (Bank A, Position E).
Bank A-9: Black Level Offset
Use the following steps to change the card's output black level. This setting is a black level offset that is not affected by the NTSC Setup function (Bank B, Position 1). For example, with Black Level Offset at 1 IRE and NTSC Setup off, the black level will be 1 IRE. With NTSC Setup on and a setup level of 7.5 IRE, the black level will be 8.5 IRE. 1. 2. Select Bank A, and rotate Function Select to position 9. Choose the desired Black Level Offset setting: * * * * Toggle Mode Select up to increase the black level offset. Hold Mode Select up to increase the black level offset continuously. Toggle Mode Select down to decrease the black level offset. Hold Mode Select down to decrease the black level offset continuously.
Bank
A
SW1 Function Select
9
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
BLK OFF (##.#) IRE
Default
0 IRE
Note
Black Level Offset is one of the six "Proc Amp" controls that can be reset using Factory Defaults (Bank A, Position E).
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-7
Bank A-A: Chroma Gain
Use the following steps to adjust the ADC-8032A's output chroma gain: 1. 2. Select Bank A, and rotate Function Select to position A. Adjust chroma gain up or down as required: * * * * Toggle Mode Select up to increase chroma gain. Hold Mode Select up to increase chroma gain continuously. Toggle Mode Select down to decrease chroma gain. Hold Mode Select down to decrease chroma gain continuously.
Bank
A
SW1 Function Select
A
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
CHROMA (###.#)%
Default
100%
Note
Chroma Gain is one of the six "Proc Amp" controls that can be reset using Factory Defaults (Bank A, Position E).
Bank A-B: Hue
Use the following steps to adjust the ADC-8032A's output hue: 1. 2. Select Bank A, and rotate Function Select to position B. Adjust hue (in degrees) as required: * * * * Toggle Mode Select up to change the hue in a clockwise direction. Hold Mode Select up to change the hue clockwise, continuously. Toggle Mode Select down to change the hue in a counter-clockwise direction. Hold Mode Select down to change the hue counter-clockwise, continuously.
Bank
A
SW1 Function Select
B
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
HUE (###.#) DEG.
Default
0 DEG.
Note
Hue is one of the six "Proc Amp" controls that can be reset using Factory Defaults (Bank A, Position E).
4-8 * Using Banks
ADC-8032A User Manual (Iss. 04)
Bank A-C: CB Gain
Use the following steps to adjust the ADC-8032A's output CB gain: 1. 2. Select Bank A, and rotate Function Select to position C. Adjust CB Gain up or down as required: * * * * Toggle Mode Select up to increase CB gain. Hold Mode Select up to increase CB gain continuously. Toggle Mode Select down to decrease CB gain. Hold Mode Select down to decrease CB gain continuously.
Bank
A
SW1 Function Select
C
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
CB GAIN (###.#)%
Default
100%
Note
CB Gain is one of the six "Proc Amp" controls that can be reset using Factory Defaults (Bank A, Position E).
Bank A-D: Chroma AGC
Use the following steps to enable or disable the Chroma AGC: 1. 2. Select Bank A, and rotate Function Select to position D. Choose the desired Chroma AGC state: * * Toggle Mode Select up to enable Chroma AGC. Toggle Mode Select down to disable Chroma AGC.
Bank
A
SW1 Function Select
D
SW2 Mode Select
+ On Off
Heads-Up Display Label
CHROMA AGC ON OFF
Default
OFF
Note
Chroma AGC is one of the six "Proc Amp" controls that can be reset using Factory Defaults (Bank A, Position E). Care must be taken when turning on the Chroma AGC. This feature allows the decoder to automatically try and compensate for any perceived chroma deficiencies. The Video Gain, Chroma Gain, and CB Gain functions all affect chroma gain and will confuse the Chroma AGC function.
Note
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-9
Bank A-E: Factory Defaults
This function allows you to return all controls to their default values, or simply the six "Proc Amp" controls by themselves. Use the following steps to select factory default values: 1. 2. Select Bank A, and rotate Function Select to position E. Select the desired default settings: * * Hold Mode Select up to reset all adjustments to their default values. Hold Mode Select down to reset the six "Proc Amp" adjustments to their default values (Video Gain, Black Level Offset, Chroma Gain, Hue, CB Gain, and Chroma AGC).
Bank
A
SW1 Function Select
E
SW2 Mode Select
+ (h) - (h) Reset All Reset Proc Amp
Heads-Up Display Label
DEFAULT ALL RST PROC RST
Default
N/A
Bank A-F: Lock/Unlock Switch Access
The Switch Access function allows you to lock or unlock user access to all adjustment parameters. The "lock" function should be performed after installation to secure all settings, and to prevent anyone from accidentally changing the settings. Note the following rules: * * When access is locked, no adjustments can be made and the Heads-Up Display is automatically turned off. When you unlock switch access and you wish to use the Heads-Up display again, you must manually enable it (Bank A, Position 1). Select Bank A, and rotate Function Select to position F. Choose the desired access mode: * * Toggle Mode Select up to lock switch access. Adjustments cannot be made, and the display is disabled. The ACCESS LED is off. Hold Mode Select down for one second to unlock switch access. Adjustments can now be made. The ACCESS LED is on.
Use the following steps to lock or unlock switch access: 1. 2.
Bank
A
SW1 Function Select
F
SW2 Mode Select
+ - (h) Locked Unlocked
Heads-Up Display Label
ACCESS LOCKED UNLOCKED
Default
LOCKED
4-10 * Using Banks
ADC-8032A User Manual (Iss. 04)
Using Bank B Functions
The following topics are discussed in this section: * * * * * Setup VI Blanking VI End SuperBlack V Bit Lock
Bank B-1: Setup
Use the following steps to enable or disable setup: 1. 2. Select Bank B, and rotate Function Select to position 1. Choose the desired setup value: * * Toggle Mode Select up to enable NTSC / PAL-M setup. Toggle Mode Select down to disable NTSC / PAL-M setup.
Bank
B
SW1 Function Select
1 *
SW2 Mode Select
+ On Off
Heads-Up Display Label
SETUP ON OFF
Default
ON* OFF**
Indicates default NTSC / PAL-M setting
** Indicates default PAL / PAL-N setting
Bank B-3: VI Blanking
Use the following steps to blank the vertical interval, or allow the signals in the vertical interval to pass through the ADC-8032A: 1. 2. Select Bank B, and rotate Function Select to position 3. Choose the desired blanking mode: * * Toggle Mode Select up to blank the vertical interval. Toggle Mode Select down to pass the vertical interval.
Bank
B
SW1 Function Select
3
SW2 Mode Select
+ Blank Pass Through
Heads-Up Display Label
VI BLANK BLANK PASS
Default
PASS
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-11
Bank B-4: VI End
The ADC-8032A has a programmable Vertical Interval function that allows you to set where the VI ends and the first line of active video begins. Everything up to (but not including) the first line of active video is considered part of the Vertical Interval and will be affected by this function. In 525line mode, signals in the vertical interval are passed without setup even if setup is enabled. The range in 525-line mode is line 20 to 22. Use the following steps to select the end point for vertical blanking: 1. 2. Select Bank B, and rotate Function Select to position 4. Choose field 1 and field 2 settings, according to the table below: * * Toggle Mode Select up to increase the line at which the VI ends. Toggle Mode Select down to decrease the line at which the VI ends.
Bank
B
SW1 Function Select
4
SW2 Mode Select
+ * Increase Decrease
Heads-Up Display Label
VI END (##)
Default
20* or 23**
525-line mode (NTSC / PAL-M) default value is selectable from 20-22
** 626-line mode (PAL / PAL-N) default value is fixed at 23
Bank B-5: SuperBlack
Use the following steps to enable or disable the SuperBlack clipping function: 1. 2. Select Bank B, and rotate Function Select to position 5. Choose the desired SuperBlack setting: * * Toggle Mode Select up to allow the input's active video signal to pass through unaltered. Toggle Mode Select down to clip any value below black.
Bank
B
SW1 Function Select
5
SW2 Mode Select
+ Pass Through Clip
Heads-Up Display Label
SUPER BLK PASS CLIP
Default
PASS
Bank B-6: V Bit Lock
Use the following steps to force the V bit on either line 10 or 20. 1. 2. Select Bank B, and rotate Function Select to position 6. Choose the desired line: * * Toggle Mode Select up to have the V bit set on line 20. Toggle Mode Select down to have the V bit set on line 10.
Bank
B
SW1 Function Select
2
SW2 Mode Select
+ Line 20 Line 10
Heads-Up Display Label
V BIT LOCK 20 10
Default
20
4-12 * Using Banks
ADC-8032A User Manual (Iss. 04)
Using Bank C Functions
The following topics are discussed in this section: * * * * * * * * * * * * Timing Mode H Delay H Reset V Delay V Reset Set Minimum Delay Freeze Mode Forced Freeze Input Loss Mode Hotswitch Mode Forced Black Forced Monochrome
Bank C-1: Timing Mode
The following topics are discussed in this section: * * * About the Timing Mode Timing Mode Summary Bank C-1: Timing Mode Procedure
About the Timing Mode
There are two versions of the ADC-8032A available. The standard ADC-8032A can be timed within one line in 37ns increments. The ADC-8032A-S with the frame synchronizer can be timed within one video frame in 37ns increments. The fine phase potentiometer (RV1) is provided for sub-pixel adjustment. The presence of a frame synchronizer means that the Frame Delay and Frame Sync modes are available. Without the frame synchronizer, the Line Delay and Line Sync modes are available. Looking at it another way, the S version provides a full frame of memory, whereas the non-S version provides a few lines of memory. This means that the non-S version provides enough timing flexibility to meet a wide variety of applications. It also means that these cards can be upgraded in the field for full frame synchronizing capabilities. The following information provides detailed explanations of when to use each mode, as well as an analysis of the advantages each mode has to offer.
Line Delay (ADC-8032A & ADC-8032A-S)
Line Delay mode uses the input signal to generate the output timing. In other words, it provides a constant delay between the input and the output. The external reference is not used in any way. This is useful in applications where a constant delay through the card is required. The delay through the card has a minimum value, as described in Chapter 7, "Specifications". Output timing can be adjusted from this minimum delay up to an additional two lines in sub-pixel increments.
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-13
Line Sync (ADC-8032A & ADC-8032A-S)
Line Sync mode uses the external reference to generate the output timing on a line-by-line basis, but uses the input signal timing to decide when a frame begins. Whenever a signal is received, the output-timing generator waits for the next falling edge of H Sync on the external reference before displaying the incoming line. The advantage of this mode is that as long as all input sources are timed to be on the same line, the output timing stays constant, regardless of which input is selected. This is very useful in that all sources to the ADC-8032A (for example, from a routing switcher) only need to be lined up to the same line. The Line Sync mode has internal latency, so that using minimum delay still means that the output video will not be lined up with the external reference. To do so would have added even more latency, which would not be desirable. However, output timing can be delayed by up to two lines from the minimum delay point on, in sub-pixel increments, so that the output video can be lined up as required. Note If two input sources are not on the same line, then switching from one source to the other causes a jump in the output timing by an exact number of lines. For example, if the two sources are 2.5 lines apart, the output will jump by either 2 or 3 lines depending on the position of the sources with respect to the external reference.
Threshold Point
As the input signal is delayed in time, there comes a point where the output timing will have to jump by exactly one line (the output must always come after the input). This point is called the threshold point. When comparing the input signal with the external reference, the threshold point is 4.25 microseconds before the falling edge of the external reference. In other words, if the input signal's falling H sync edge is 4.25 microseconds before the external reference's falling H sync edge, the input signal is said to be on the threshold point. In addition, there is built in hysteresis so that if an input source is on the threshold point, the output timing will be constant and will not jump back and forth by a line if the input signal varies slightly. However, if the input signal is exactly on the threshold point, the output timing may vary from one power up sequence to the other. In other words, the card may power up with different timing than the previous time it was powered-up. To avoid this condition, it is recommended to keep the input signal away from the threshold point. One microsecond can be considered a safe distance. Note In Line Sync mode, you must keep the falling H sync edge of the incoming video away from the threshold point.
Frame Delay (ADC-8032A-S)
The Frame Delay mode is identical to the Line Delay mode, except that the output timing can be delayed by up to a full frame of video. By using almost a full frame of delay, it is possible to set apparent negative timing, making it look like the output occurs before the input, although delayed by 1 frame.
Frame Sync (ADC-8032A-S)
The Frame Sync mode makes it possible to use asynchronous sources. The output timing is generated entirely based on the external reference. Whether a synchronous or an asynchronous source is used, output timing is constant. The delay through the card will be the minimum latency (in the order of microseconds) to a full frame of delay.
4-14 * Using Banks
ADC-8032A User Manual (Iss. 04)
Timing Modes
This section provides a summary of all Timing Modes.
Line Delay
Use when you do not have an S version and need constant delay through the card. * * * * Output timing based on input timing Ignores external reference Has the lowest minimum delay through the card Two-line output timing adjustment window
Line Sync
Use when you do not have an S version and need constant output timing even though input timing may change. This is the recommended mode for the non-S version. * * * Output timing based on external reference (line by line only) If input sources are timed to be on the same line, the output timing will be constant. Keep input timing away from the threshold point.
Frame Delay
Use when you have an S version and need constant delay through the card. * * * * Output timing based on input timing. Ignores external reference. Has the lowest minimum delay through the card. Output timing adjustment window has infinite phasing over a full frame.
Frame Sync
Use when you have an S version and need constant output timing, or when the input is asynchronous to house reference. * * * Input can be asynchronous. Output timing is constant, regardless of input timing. Output phasing is infinite over a full frame, and the delay through the card varies from the minimum processing delay up to the minimum processing delay plus a full frame.
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-15
Bank C-1: Timing Mode Procedure
Use the following steps to set the timing mode: 1. 2. Select Bank C, and rotate Function Select to position 1. Select the desired timing mode according to the following table. * * Toggle Mode Select up to advance up the list. Toggle Mode Select down to descend down the list.
Bank
C
SW1 Function Select
1
SW2 Mode Select
+ Frame Sync * Frame Delay * Line Sync Line Delay
Heads-Up Display Label
TIME MODE FS FD LS LD
Default
LS (FS on S models)
* Indicates ADC-8032A-S only
Bank C-2: H Delay
Use the following steps to adjust the output's H Delay: 1. 2. Select Bank C, and rotate Function Select to position 2. Increase or decrease the H Delay as required: * * * * Toggle Mode Select up to increase H Delay by half a pixel (one 27MHzclock period) with each toggle. Hold Mode Select up to increase H Delay continuously. Toggle Mode Select down to decrease H Delay by half a pixel (one 27MHz-clock period) with each toggle. Hold Mode Select down to decrease H Delay continuously.
Bank
C
SW1 Function Select
2
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
H DELAY (#)
Default
0
Please note the following important points regarding H Delay: * * * If you cross over the maximum H Delay, the value returns to 0 (zero) and the V Delay value increments by 1. Crossing the minimum delay returns the H Delay value to 1715 (NTSC) or 1725 (PAL) and decrements the V Delay value by 1. Sub-pixel timing adjustments can be made using the RV1 Fine Phase Adjust potentiometer on the front edge of the card. Turning the pot clockwise increases delay, whereas turning it counter-clockwise decreases the delay. The range is approximately 45 ns, which is slightly longer than the step size of the H Delay function.
4-16 * Using Banks
ADC-8032A User Manual (Iss. 04)
Bank C-3: H Reset
Use the following steps to reset just the H Delay value to 0 (zero). This function is particularly useful if your adjustment range is far off the mark, or if you simply want to quickly return to zero. 1. 2. Select Bank C, and rotate Function Select to position 3. Reset H Delay as required: * Toggle Mode Select up to reset H Delay to 0.
Bank
C
SW1 Function Select
3
SW2 Mode Select
+ Zero No action
Heads-Up Display Label
H RESET ZERO
Default
N/A
Bank C-4: V Delay
Use the following steps to adjust the output's V Delay: 1. 2. Select Bank C, and rotate Function Select to position 4. Increase or decrease the V Delay as required: * * * * Toggle Mode Select up to increase V Delay by one line. Hold Mode Select up to increase V Delay continuously. Toggle Mode Select down to decrease V Delay by one line. Hold Mode Select down to decrease V Delay continuously.
Bank
C
SW1 Function Select
4
SW2 Mode Select
+ Increase Decrease
Heads-Up Display Label
V DELAY (#)
Default
0
Bank C-5: V Reset
Use the following steps to reset just the V Delay value to 0 (zero). 1. 2. Select Bank C, and rotate Function Select to position 5. Reset V Delay as required: * Toggle Mode Select up to reset V Delay to 0.
Bank
C
SW1 Function Select
5
SW2 Mode Select
+ Zero No action
Heads-Up Display Label
V RESET ZERO
Default
N/A
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-17
Bank C-6: Set Minimum Delay
Use the following steps to reset both the H Delay and V Delay values to 0 (zero). 1. 2. Select Bank C, and rotate Function Select to position 6. Reset all delays as required: * Toggle Mode Select up to reset H Delay and V Delay to 0.
Bank
C
SW1 Function Select
6
SW2 Mode Select
+ Zero No action
Heads-Up Display Label
MIN DEL ZERO
Default
N/A
Bank C- 7: Input Mode
The Input Mode function selects what type of video is being input. The choices are: * * Standard - standard VTR - input signals that do not have a stable timebase, such as from VTR's or VCR's
When VTR is selected as the video Input Mode, an external reference is required to reclock the input signal to the house clock. The external reference provides stable output timing. Use the following steps to set the Input Mode: 1. 2. Select Bank C, and rotate Function Select to position 7. Select the desired Input mode according to the following table. * * Toggle Mode Select up to set VTR mode Toggle Mode Select down to set STANDARD mode.
Bank
C
SW1 Function Select
7
SW2 Mode Select
+ VTR mode STANDARD mode
Heads-Up Display Label
IN MODE VTR STAND
Default
STAND
Note Note
A reference must be connected when in VTR Mode. A reference must be connected when in VTR Mode. This mode affects the Hotswitch Mode. Timebase error-prone signals such as from a VCR will falsely trigger the hotswitch detector. Thus, an Input Mode selection of VTR will force the Hotswitch Mode to OFF.
4-18 * Using Banks
ADC-8032A User Manual (Iss. 04)
Bank C-8: Freeze Mode
The input image can be frozen (ADC-8032A-S only) if any of the following conditions occur: * * * The user selects Manual Freeze (Forced Freeze, Bank C, Position 9) There is a loss of input signal (Input Loss Mode, Bank C, Position A) A hotswitch occurs (Hotswitch Mode, Bank C, Position B)
The Freeze Mode function allows you to set the type of freeze that occurs: Field 1, Field 2, or Full Frame. Use the following steps to set the freeze mode: 1. 2. Select Bank C, and rotate Function Select to position 8. Select the desired mode according to the table below: * * Toggle Mode Select up to advance up the list. Toggle Mode Select down to descend down the list.
Bank
C
SW1 Function Select
8
SW2 Mode Select
+ Frame Field 2 Field 1
Heads-Up Display Label
FRZ MODE FRAME FLD 2 FLD 1
Default
FLD 1
Bank C-9: Forced Freeze
The output can be manually frozen (ADC-8032A-S only) using the Forced Freeze mode. When enabled, the freeze will affect either field 1, field 2 or the entire frame (as determined by the Freeze Mode function). Use the following steps to enable or disable the Forced Freeze mode: 1. 2. Select Bank C, and rotate Function Select to position 9. Select the desired mode: * * Toggle Mode Select up to freeze the image. The FREEZE LED is on. Toggle Mode Select down to un-freeze the image, and allow input video to pass through. The FREEZE LED is off.
Bank
C
SW1 Function Select
9
SW2 Mode Select
+ Freeze Pass Through
Heads-Up Display Label
FREEZE FORCE PASS
Default
PASS
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-19
Bank C-A: Input Loss Mode
The Input Loss Mode function selects what type of video appears at the system's four outputs when the input signal is lost or invalid. These choices are available: * * * Black - SDI black. No Output - flat line, no signal present. Freeze - the last valid image is automatically frozen (ADC-8032A-S only). The freeze will affect either field 1, field 2 or the entire frame (as determined by the Freeze Mode function). Re-initialize - the card will re-initialize itself every 1.5 seconds. (This option may be removed on future revisions.)
*
When a valid input signal is restored, the Input Loss Mode setting is ignored. Use the following steps to set the Input Loss Mode: 1. 2. Select Bank C, and rotate Function Select to position A. Select the desired mode according to the table below: * * Toggle Mode Select up to advance up the list. Toggle Mode Select down to descend down the list.
Bank
C
SW1 Function Select
A
SW2 Mode Select
+ Freeze No Output Black
Heads-Up Display Label
IN LOSS RE-INIT FREEZE NO OUTPUT BLACK
Default
BLACK
Important
It is recommended that the Hotswitch Mode and Input Loss Mode be set the same with either: both set to freeze, or both set to black. There is circuitry in the sync stripper that removes unwanted impulses to make the circuit more noise tolerant. During a hotswitch, this could cause the ADC-8032A to interpret the signal has been lost. Since the Input Loss mode overrides the Hotswitch mode setting, having one set to freeze and the other set to black could lead to a momentary glitch on the screen.
Bank C-B: Hotswitch Mode
The ADC-8032A uses a phase-locked-loop (PLL) to synchronize its pixel clock to the incoming signal's line rate. Because of this, any disturbance to the incoming line rate, such as an untimed switch outside the lock window of the PLL, will cause the PLL to lose lock. It can take several fields before the PLL can regain lock, and until it does so, the decoder cannot properly decode the incoming video. The result is that untimed switches will result in a disruption to the output video. To mask this disruption, a hotswitch mode was created. This is accomplished by momentarily freezing the last good frame, or momentarily going to black while the untimed switch occurs. Going to black is recommended since the output can be forced to black as soon as the hotswitch condition is detected. Freezing must wait until the next field, in which case a single corrupted field could get through to the output. In Frame Sync, the output timing will be undisturbed as it is based on the external reference. In Line Sync mode, as long as the input sources are on the same line relative to the external reference, and they do not cross the threshold point (see Bank C-1 Timing Mode for details on the threshold point),
4-20 * Using Banks
ADC-8032A User Manual (Iss. 04)
then the output timing will also be undisturbed. In all other cases, the output timing will be disturbed any time an untimed switch is made at the input of the ADC-8032A. This function sets the mode or disables it. Three choices are available: * * * Off - disables the Hotswitch Mode. Black - the output momentarily cuts to black when an untimed switch is made at the input. Freeze - (ADC-8032A-S only) the last valid image is momentarily frozen. The freeze will affect either field 1, field 2 or the entire frame (as determined by the Freeze Mode function).
In either case, the output returns once the card has synchronized to the input. Use the following steps to set the Hotswitch Mode: 1. 2. Select Bank C, and rotate Function Select to position B. Select the desired mode according to the table below: * * Toggle Mode Select up to advance up the list. Toggle Mode Select down to descend down the list.
Bank
C
SW1 Function Select
B
SW2 Mode Select
+ Freeze Black Off
Heads-Up Display Label
HOTSW MD FREEZE BLACK OFF
Default
OFF
Note
Freeze hotswitching is not supported in Line Delay, Line Sync and Frame Delay timing modes. If one of these timing modes is selected and freeze hotswitching is enabled, the hotswitch will go to black instead. Because output timing is disrupted in Line Delay and Frame Delay modes, hotswitching is not guaranteed to go completely black. These two timing modes should never be used if the input source is switched while on air, since the output timing will be affected, and this could affect equipment downstream of the ADC-8032A. It is recommended that the Hotswitch Mode and Input Loss Mode be set the same with either: both set to freeze, or both set to black. There is circuitry in the sync stripper that removes unwanted impulses to make the circuit more noise tolerant. During a hotswitch, this could cause the ADC-8032A to interpret the signal has been lost. Since the Input Loss mode overrides the Hotswitch mode setting, having one set to freeze and the other set to black could lead to a momentary glitch on the screen. Timebase error-prone signals such as from a VCR will falsely trigger the hotswitch detector. Thus if the Input Mode is set to VTR it forces the Hotswitch Mode to OFF.
Important
Important
Important
ADC-8032A User Manual (Iss. 04)
Using Banks * 4-21
Bank C-C: Forced Black
This selection forces the output to black (SDI). Use the following steps to enable or disable the Forced Black mode: 1. 2. Select Bank C, and rotate Function Select to position C. Select the desired mode according to the table below: * * Toggle Mode Select up and hold for one second to force the output to black. Toggle Mode Select down to disable the Forced Black mode.
Bank
C
SW1 Function Select
C
SW2 Mode Select
+ (h) On Off
Heads-Up Display Label
FRCD BLK ON OFF
Default
OFF
Bank C-D: Forced Mono
This selection forces the output to monochrome (SDI). Use the following steps to enable or disable the Forced Monochrome mode: 1. 2. Select Bank C, and rotate Function Select to position D. Select the desired mode according to the table below: * * Toggle Mode Select up and hold for one second to force the output to monochrome. Toggle Mode Select down to disable the Forced Monochrome mode.
Bank
C
SW1 Function Select
D
SW2 Mode Select
+ (h) On Off
Heads-Up Display Label
FRCD MONO ON OFF
Default
OFF
4-22 * Using Banks
ADC-8032A User Manual (Iss. 04)
SMPTE 269M Fault Reporting
In This Chapter
This chapter contains the following sections: * * * * Overview Jumper Setup Frame Connections Details
Overview
The SMPTE 269M Fault Reporting system, also known as an SMPTE "alarm", provides indication if one or more frame modules encounter a fault or an abnormal condition. The ADC-8032A module provides a jumper to enable SMPTE-269M fault reporting. The card connects by means of an internal interface circuit to an auxiliary telco connector on RossGear 8000 series frames. When the frame connection is interfaced with a customer-designed system of LEDs or audible alarms, faults can be traced to a specific frame when a card fault occurs within that frame. The following diagram illustrates a general arrangement for SMPTE 269M alarm reporting:
Figure 5. SMPTE 269M Alarm Reporting: Internal interface and typical connections
ADC-8032A User Manual (Iss. 04)
SMPTE 269M Alarm Reporting * 5-1
Jumper Setup
If fault reporting for the ADC-8032A is desired, use jumper JP4 - 269M Fault Report to set up the card. 1. To access the jumper, remove the card from the frame by pressing down the white card ejector tab and pulling the card from the frame slot. 2. Observing all static discharge and handling precautions, place the card with the component side facing up on a clean flat surface. 3. To enable SMPTE fault reporting, set jumper JP4 to EN position. See the Jumper Setup section in Chapter 2 "Installation and Setup". 4. To disable SMPTE fault reporting, set jumper JP4 to DIS position. See the Jumper Setup section in Chapter 2 "Installation and Setup". 5. To return the card to the designated frame installation slot, hold the ADC-8032A card by the edges and carefully align the card edges with the slots in the frame. Then fully insert the card into the frame until the rear connection plug is properly seated.
Frame Connections
The SMPTE 269M Fault Reporting connection on RossGear 8000 series frames is provided by the auxiliary telco connector, AUX A, for interfacing with a customer-designed alarm system.
Aux A Connectors for SMPTE 269M Fault Reporting
Figure 6. SMPTE 269M Alarm Reporting Frame Connections
Connect the frame's AUX A connector to your facility's SMPTE alarm circuit.
Details
The fault report contacts are closed when the card detects an internal failure or a power loss condition. Some internal failures are: * Failure of the card to initialize * Failure in the fault reporting circuitry * Failure to detect a valid analog input signal to the card For additional information on alarm system design, refer to the SMPTE document ANSI/SMPTE 269M - 1994.
5-2 * SMPTE 269M Fault Reporting
ADC-8032A User Manual (Iss. 04)
Comlink
In This Chapter
This chapter contains the following sections: * * * Overview Cable Construction Connection and Configuration
Overview
The board's Terminal Display feature uses the Comlink BNC (7) to establish a connection between a PC and the ADC-8032A. When properly connected, you can view your setup parameters on a PC running VT-100 terminal emulation. All tables are output in ASCII format using an RS-485 interface. Because of the nature of the frame, it is not possible to have a true differential signal. In this situation, using a BNC on the frame side, the connection is single-ended. Only the center conductor carries information, while the shield is grounded. Important! Ensure that the PC and the card frame are at the same ground potential in order to avoid ground loops. Although the interface is RS-485, the Comlink can function with most modern RS-232 equipment, thereby making it easy and convenient to use with standard PC COM ports. To connect the Comlink between the ADC-8032A and your PC, you require a coax adapter cable with a BNC connector at one end, and either a 9-pin or 25-pin RS-422 or RS-232 connector at the other end.
ADC-8032A User Manual (Iss. 04)
Comlink * 6-1
Cable Construction
Construct a custom coax cable adapter as follows: * * On the Frame end of the coax cable, no change to the BNC cable is required. Ensure that the pin and shield are properly connected. On the PC end of the cable, make the following connections according to whether your PC port uses a 9-pin "D" or a 25-pin "D" connector: Regardless of whether your PC port uses a 9-pin "D" or a 25-pin "D" connector, the pin-out configuration may vary. Always check your PC's Technical Guide to determine the correct pin-outs for your computer. The RX and GND pin-outs will vary from machine to machine.
Important!
9-Pin Connections
The following diagram illustrates a sample connection using a typical pin-out configuration for a PC's 9-pin D-type connector.
5 9
4 8
3 7
2 6
1
Figure 7. D-9 to BNC Connections
1. 2.
Connect the center conductor of the coax to the pin 2 (RX) on your serial port connector. Connect the shield of the coax to the ground pin 5 (GND) on your serial port connector.
25-Pin Connections
The following diagram illustrates a sample connection using a typical pin-out configuration for a PC's 25-pin D-type connector.
13 25
12 24
11 23
10 22
9 21
8 20
7 19
6 18
5 17
4 16
3 15
2 14
1
Figure 8. D-25 to BNC Connections
1. 2.
Connect the center conductor of the coax to the pin 3 (RX) on your serial port connector. Connect the shield of the coax to the ground pin 7 (GND) on your serial port connector.
6-2 * Comlink
ADC-8032A User Manual (Iss. 04)
Connection and Configuration
Once you have constructed the Comlink adapter cable, connect it and configure the PC as follows: 1. 2. Connect the cable between your PC's serial port and BNC 7 on the rear panel of the ADC-8032A. With the custom cable properly connected, set up your PC's serial port parameters as follows: * * * * * 3. 19.2 K baud rate 8 data bits No parity 1 stop bit No flow control
On your PC, run a program that uses VT-100 terminal emulation, such as Terminal.exe or HyperTerminal. With the ADC-8032A powered up, you should now have all setup parameters visible on the PC, as illustrated in the sample screen below.
Figure 9. Sample Terminal Display
ADC-8032A User Manual (Iss. 04)
Comlink * 6-3
6-4 * Comlink
ADC-8032A User Manual (Iss. 04)
Specifications
In This Chapter
This chapter contains the Technical Specifications table.
ADC-8032A User Manual (Iss. 04)
Specifications * 7-1
Technical Specifications
Table 6. ADC-8032A - Technical Specifications
Category
Parameter
Signal Standards Accepted Number of Inputs
Specification
NTSC, PAL, PAL-M, PAL-N 1 1V p-p nominal 75 terminating >48dB to 6MHz >52dB @ 50/60Hz SMPTE 259M-C, 270Mb/s 525/625 lines, 10 bits 4 >18dB to 270MHz 800mV 5% < 30mV >800pS (20 - 80%, 15%) <10% typical NTSC, PAL, PAL-M, PAL-N 1 75 >40dB to 5MHz 0.25dB to 5MHz, < -0.8dB @ 5.75MHz > 56dB to 5.5MHz, unweighted > 56dB to 5.5MHz, unweighted Infinite with frame sync, 2 lines without frame sync
Composite Video Input
Composite Video Input Impedance Return Loss Common Mode Rejection Signal Standards Number of Outputs Output Return Loss Signal Level DC Offset Rise and Fall Time Overshoot Signal Standards Accepted
Component SDI Output
Analog Reference
Number of Inputs Input Impedance Return Loss Luminance Frequency Response RMS SNR, Luma Channel RMS SNR, Chroma Channel H and V phasing
Performance
Minimum Delay in Line/Frame Delay Mode Power Consumption TTL Tracking Delay Pulse
Minimum Delay
3 Line + 23S
Total ADC-8032A ADC-8032A-S
7.9W up to 2 video lines up to 2 video fields
Specifications are subject to change without notification
7-2 * Specifications
ADC-8032A User Manual (Iss. 04)
Ordering Information
In This Chapter
This chapter contains: * * * Ordering information for the ADC-8032A and related products Contact information for Ross Video Warranty and Repair Policy
ADC-8032A and Related Products
Standard Equipment
* * ADC-8032A Analog Composite to SDI Decoder* ADC-8032A-S Analog Composite to SDI Decoder with Frame Synchronizer*
Optional Equipment
* * * * * * * * 8032AD-004 Analog Composite to SDI Decoder User Manual (additional User Manual) FSU-8032A Frame Synchronizer Upgrade (replacement microprocessor for adding Frame Sync function to standard ADC8032A) EXT-8100 Extender Board (module servicing extension) DFR-8104A Digital Products Frame and Power Supply (PS-8102)* (1RU, holds 4 modules, includes 1 power supply) DFR-8104A-C Digital Products Frame with Cooling Fan Module and Power Supply (PS-8102)* (1RU, holds 4 modules, includes 1 power supply) DFR-8110A Digital Products Frame and Power Supply (PS-8102)* (2RU, holds 10 modules, includes 1 power supply) DFR-8110A-C Digital Products Frame with Cooling Fan Module and Power Supply (PS-8102)* (2RU, holds 10 modules, includes 1 power supply) CFM-8104A Cooling Fan Module (upgrade cooling kit for standard DFR-8104A)
ADC-8032A User Manual (Iss. 04)
Ordering Information * 8-1
* * * * *
CFM-8110A Cooling Fan Module (upgrade cooling kit for standard DFR-8110A) PS-8102 Power Supply (85-264 volts) (redundancy option power supply for Ross 8000 series 2RU digital product frames) FSB-7110 Rear Support Bars and Brackets (additional support for rear frame-to-rack mounting) CRB-8110A Card Retaining Bracket (module retainer used in field installations such as mobile trucks etc.) CSB-8100 Cable Support Bracket (cable support bar for rear of digital frames) * One User Manual is supplied with each of these RossGEAR products.
Your ADC-8032A Analog Composite to SDI Decoder is part of the RossGEAR family of products. Ross Video Limited offers a full line of RossGEAR Digital Terminal Equipment including Distribution, Conversion, Monitoring, Synchronizers, Encoders, Decoders, AES, Keyers, Control Switchers, as well as Analog Audio and Video products.
Warranty and Repair Policy
The RossGear ADC-8032A is warranted to be free of any defect with respect to performance, quality, reliability, and workmanship for a period of FIVE (5) years from the date of shipment from our factory. In the event that your RossGear ADC-8032A proves to be defective in any way during this warranty period, Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics. Should you find that this RossGear ADC-8032A has failed after your warranty period has expired, we will repair your defective product for as long as suitable replacement components are available. You, the owner, will bear any labor and/or part costs incurred in the repair or refurbishment of said equipment beyond the FIVE (5) year warranty period. In no event shall Ross Video Limited be liable for direct, indirect, special, incidental, or consequential damages (including loss of profits) incurred by the use of this product. Implied warranties are expressly limited to the duration of this warranty. This RossGear ADC-8032A Analog Composite to SDI Decoder User Manual of our Digital Products line provides all pertinent information for the safe installation and operation of your RossGear Product. Ross Video policy dictates that all repairs to the RossGear ADC-8032A are to be conducted only by an authorized Ross Video Limited factory representative. Therefore, any unauthorized attempt to repair this product, by anyone other than an authorized Ross Video Limited factory representative, will automatically void the warranty. Please contact Ross Video Technical Support for more information.
In Case of Problems
Should any problem arise with your RossGear ADC-8032A, please contact the Ross Video Technical Support Department. (Contact information is supplied at the end of this publication.) A Return Material Authorization number (RMA) will be issued to you, as well as specific shipping instructions, should you wish our factory to repair your RossGear ADC-8032A. A temporary replacement module, if required, will be made available at a nominal charge. Any shipping costs incurred, will be the responsibility of you, the customer. All products shipped to you from Ross Video Limited, will be shipped collect. The Ross Video Technical Support Department will continue to provide advice on any product manufactured by Ross Video Limited, beyond the warranty period without charge, for the life of this equipment.
8-2 * Ordering Information
ADC-8032A User Manual (Iss. 04)
Notes:
ADC-8032A User Manual (Iss. 04)
Ordering Information * 8-3
Contact Us
Contact our friendly and professional support representatives for the following: * * * * Name and address of your local dealer Product information and pricing Technical support Upcoming trade show information
PHONE
General Business Office and Technical Support After-hours Emergency Fax General Information Technical Support Ross Video Limited Ross Video Incorporated
613 * 652 * 4886 613 * 652 * 4886 ext. 333 613 * 652 * 4425 solutions@rossvideo.com techsupport@rossvideo.com 8 John Street, Iroquois, Ontario, Canada K0E 1K0 P.O. Box 880, Ogdensburg, New York, USA 136690880
E-MAIL
POSTAL SERVICE
Visit Us Please visit us at our website for: * * * * * * * Company information Related products and full product lines On-line catalog Trade show information News Testimonials EFD-compliant product information (Engineer Friendly Documentation) (EFD is a project promoted by SBE to provide a web-based platform for the open sharing of technical specifications between manufacturers and engineers, using an XML formatted set of suggested templates, to make it easier for engineers to find the technical information they need to plan a smooth project. Ross Video Limited is proud to support our broadcast industry engineers by participating in this important initiative.)

▲Up To Search▲

Price & Availability of ADC-8032A

	To Download ADC-8032A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .